AUTONET TV

Such a Little Part (Climate Control Resistor)

You expect your heater/air conditioner to work like it should.  You have a control for temperature and one for fan speed.  You even have a control for what vents the air comes out of. 

Don't be surprised one day if your blower fan develops a mind of its own and starts going crazy.  Most of the time, you may find that it starts blowing at full speed, and nothing you do to try to control it does any good.  This is what may be happening.

Your blower motor has an electronic component called a resistor.  It does what its name says; it offers resistance.  When you want the fan to run more slowly, you turn the fan speed down.  That resistor accomplishes that by turning its resistance up.  When the resistor fails, the power has nothing to slow it and the fan speeds up. 

It's a small part and can fail due to age or corrosion.  It's usually not an expensive part, either, but it's often found in a location that's not that easy for the technician to get to.  That means labor costs will vary depending on the design of your vehicle. 

Occasionally, a faulty resistor can cause the blower motor not to work at all or only partially come on.  But other things can cause that as well, such as a faulty fan switch or vent control. 

This is where a technician's training comes in.  Special equipment can track down precisely where the issue is so you can be assured the correct part is being replaced.

It's just not pleasant when the blower motor isn't following orders.  Have your service facility check it out so you can be the blower's boss, like it should be. 

AutoChoice Service Center Inc.
2009 S. Yost Ave.
Bloomington, Indiana 47403
812-339-9898

Something to Latch On To (Hood Latch Safety)

The other day, a driver was trying to open his vehicle's hood so he could add some windshield washer fluid.  But when he pulled the hood release inside the car, nothing happened. 

Usually, opening any hood is a 2-step process.  You pull the hood release (which is usually a handle under the dashboard to the left of the steering column) and listen for the hood to pop up slightly. (It doesn't open all the way because it has a safety latch to prevent you from accidentally opening it up while you're driving.) Then, you get out and find the latch, usually through the grille near the hood.  There's a little handle on it which you push, slide or pull (there are a few different types) at which point the hood can be opened up all the way. 

But in this driver's case, the hood would not release at all when he pulled the handle inside.  Not knowing what to do, he called his service advisor, who told him to bring it over.  The reason? A hood with a broken latch could be a safety hazard since it is possible it's not securely closed. And in this condition, it's possible for the hood to suddenly release while you are driving, obscuring your view of the road. 

Latch issues can be caused by many things, perhaps a broken cable between the hood release and the latch.  It's possible that cable just detached or frayed after being opened so many times.  If a hood release cable isn't kept lubricated, it can corrode and just lock up.

In this driver's case, the cable had corroded and broken, so it had to be replaced.  Unfortunately, many times you won't know you have a problem with your hood latch until one time you pull it and it breaks without warning.  When your vehicle is in for routine maintenance like an oil change, a technician will often keep an eye out for signs that your hood latch needs attention so you don't get "locked" out of your engine compartment.

AutoChoice Service Center Inc.
2009 S. Yost Ave.
Bloomington, Indiana 47403
812-339-9898

Some New Boots (Suspension Maintenance)

There are some boots that don't come in a shoe box and aren't worn on your feet.  They are called axle or CV boots, and they can be important parts for many vehicles.

That CV stands for constant velocity.  CV axles are mainly used in front-wheel drive and all-wheel drive vehicles. They're also used in some rear-wheel drive vehicles with independent suspensions.  They have two CV joints, one inner and one outer, placed between the axle and the drive wheels.  That way the vehicle's engine power can drive the wheels, no matter what angle they are.  They also adjust for the different speeds wheels turn as they go around corners. 

Because roads are full of all sorts of hazards (dirt, oil, water, grime), these CV joints need to be protected.  They also have grease in them to keep the bearings moving smoothly.  That's the job of the rubber boots that are supposed to keep that debris out.  These CV or axle boots are made of rubber or plastic and usually last a long time without any problem.  But sometimes they fail, either from being hit by debris or age causing the rubber or plastic to deteriorate.  That can allow the grease to leak out of the joint and the moisture to get in.  And that's where the trouble is.

So it's important to have a vehicle's CV boots checked periodically, especially when they begin to have more than 100,000 miles/160,000 kilometers on them.  A technician inspects them for tears or cracks.  Sometimes if the problems are found early enough, the boots can be replaced and the joints can be re-packed with grease. 

But sometimes the CV joint can wear out even though the boot is intact.  When the CV joint fails, you might hear a grinding, humming or clicking noise and feel vibration.

Some of these can be difficult to access for service, so many service advisors will recommend replacing the joints and boots at the same time.  Just remember, new CV boots won't make a fashion statement, but they will keep your vehicle going down the road for years to come.

AutoChoice Service Center Inc.
2009 S. Yost Ave.
Bloomington, Indiana 47403
812-339-9898

The Key Won't Turn! (Ignition Problems)

You've just arrived at the store shopping and you're ready to head home.  You put your key in the ignition and… oh, no! The ignition won't turn! What do you do now?

Don't panic.  There are some things you can do to get going again.  The first thing to do is see if you have a locking steering wheel, an anti-theft feature that was introduced around 1970.  Sometimes it sticks.  Move the steering wheel side to side while you try to turn the key and you might be able to get it to release. 

Another thing to check is to see if your vehicle is in gear.  Most vehicles will only allow you to start the ignition if it's in park or neutral.  If you have an automatic transmission vehicle and it is in park, try jiggling the shift lever and try the key again.  Sometimes the safety mechanism doesn't properly make contact or gets a little sloppy. 

If both of these don't work, it could be your vehicle's battery is dead.  Some newer electronic systems require power so the key can turn. Others have alarm systems that detect if doors are open. 

Other issues that can cause key problems include something jammed in the lock cylinder.  Or some of the springs or pins inside may be stuck.  Consider that it may be the key itself.  Sometimes they get bent or simply wear out from the number of times they've been put in and taken out of the cylinder.

No matter what the cause, the first time this happens you should have your repair service facility check it out. That’s because if it happens once, it can happen again.  Even if you were able to get going again on your own, your ignition/key has warned you that something's wrong.  Have it checked out by a pro so you’re not locked into a bad situation.

AutoChoice Service Center Inc.
2009 S. Yost Ave.
Bloomington, Indiana 47403
812-339-9898

How to Radiate Cool (Radiator Care)

There's nothing that radiates cool like a vehicle radiator that's helping to keep your engine running at the proper temperature.  You don't have to baby it, but you can't simply ignore it, either. 

Let's take a quick dive under the hood to let you know what the radiator is doing.  It takes the heat your engine produces and moves that heat outside.  It's not an easy job and heat is an engine's number one enemy.  Now that you're thinking how nice you want to be to your radiator, we have a couple of ideas how you can take care of it.

The easiest thing is to pay attention to your vehicle's temperature gauge. If it gets in the "too hot" or "not hot enough" range, have it checked out soon.  Make sure your coolant is kept at the correct level and if you see a trend that you have to add coolant more than a couple of times a year, you might have a leak.

Even if there are no obvious problems, every couple of years or so, consider taking your vehicle in for radiator maintenance.  A technician can run a pressure check for leaks and ensure that the thermostat and radiator cap are working correctly.  The technician will check that fans are running like they should so they can move air over the radiator and heat away from the coolant inside.

Ask your service advisor when you should have your radiator flushed and coolant replaced according to the manufacturer's recommended intervals.  In addition to cooling, coolant has corrosion inhibitors which stop working after a while.  Without those corrosion inhibitors, the inside of your radiator can literally start rotting away.  Keep in mind that the coolant level must be kept at manufacturer's specifications since if those corrosion-preventing chemicals aren't touching the metal, they're not preventing corrosion. 

Different vehicles use different coolants, so your service facility will make sure yours is getting the correct one.  Keep your coolant system happy and one day, maybe you can order up a custom license plate, "RAY-D-8."

AutoChoice Service Center Inc.
2009 S. Yost Ave.
Bloomington, Indiana 47403
812-339-9898

Slippery When Wet (Driving on Wet Leaves)

When the leaves fall, you might take a sightseeing trip to see them at peak color.  Or you may simply live in a spot where there are a lot of trees.  When those leaves get wet, you'd be surprised to learn just how slippery they can be. 

We all know ice is slippery to drive on.  What causes tires to slip on ice is a thin layer of water that comes between the road and your tires.  Wet leaves can have the same effect.  The surfaces of leaves are super slick when they're dry, even worse when you add a little moisture.  There's one other thing about leaves.  They are smaller than each tire's footprint, so your tread grips the pavement with uneven traction.

One study showed that your stopping distance can more than double on a surface covered with wet leaves when compared to that same road when it's dry.  Double! That can spell trouble.  So if you find yourself heading into an area with wet leaves on the road, slow down before you get into a jam.  If you do start skidding, use the same driving techniques as you would on ice.  Let off the accelerator, resist jamming on the brakes and steer into the skid.  Again, speed can get you into trouble fast on a slippery surface.

One thing that can help is having tires that are appropriate for the way you drive and the places you travel.  Your service advisor can offer suggestions for tires that are right for you.  Have a technician examine your tread depth and the condition of your tires' rubber.  Sun can break down rubber over time, and age can cause tires to fail, even if their tread seems to be deep enough. 

Your tire is the point of traction between your vehicle and the road.  Uncontrolled skids spell trouble and danger.  Slow down when you see wet leaves on the road.  They can make traction disappear before you know it.

AutoChoice Service Center Inc.
2009 S. Yost Ave.
Bloomington, Indiana 47403
812-339-9898